×
close
click to zoom in

12V 100A Flashing Power Supply and 100A HD Battery Charger - PL6800

(No reviews yet) Write a Review
$0.00
Part Number
BDBV-PL6800
UPC:
010271026968
5 customers are viewing this product
The PL6800 is designed to provide stable power, on demand up to 100 amps, to a vehicle electrical system to support module reprogramming. It is also designed specifically for fleet service battery charging with a maximum charge rate of 100 amps, to quickly and effectively bring 4- and 8-battery Group 31 packs back to full charge. In power supply mode, the PRO-LOGIX PL6800 provides power to maintain vehicle electrical system voltage at a preset level, increasing its output in response to system load increases to maintain a stable power environment for successfully reprogramming. It features a voltage output range of 13.1-14.9V, adjustable in 0.1V increments. allowing the operator to dial the output in exactly as specified by the supplier of the vehicle under service. It features fast load responsiveness for ultra-quick recovery from system demand increases. It also delivers its massive power with minimal voltage ripple (<100mV), providing a clean flow of power to the vehicle without risk of programming interference. In charging mode, the PL6800 utilizes advanced microprocessor-controlled logic to precisely deliver a fully automatic charging routine designed to optimally charge and maintain each battery or battery pack serviced. The PL6800 features the ability to properly charge a wide variety of lead acid battery types, including Conventional, AGM, Spiral Wound, Start-Stop, Deep Cycle and Marine batteries ? for virtually any lead acid battery type installed in a vehicle, the PL6100 can deliver a proper, beneficial charge. The PL6800 adapts its charging approach based on the needs of each battery or battery pack it services. Such adaptations can include activating a soft start mode on deeply discharged batteries, a battery repair mode on older/distressed batteries and temperature compensation when charging in extreme temperatures. It also incorporates numerous features to make charging safer for the operator and the vehicle/battery being charged.
  • 0-100A (on demand) power supply mode to maintain system voltage
  • Extra-long 13' cable reach
  • PowerJaw clamps provide improved access to hard-to-reach batteries
  • PowerJaw clamps allow the hood to be closed (most vehicles) during ADAS calibration
  • Requires 20A service
  • Power supply mode provides optimal support for vehicle reprogramming and ADAS recalibration
  • Power supply mode has minimal voltage ripple (<100mV)
  • Power supply mode features Rapid Load Response (RLR) technology
  • 100/40/10A charging modes allow quick, efficient charging of all battery sizes
  • Properly charges Flooded, AGM, Spiral Wound, Deep Cycle and Marine Batteries
  • Forced start mode allows charging of totally dead batteries
  • Battery repair mode overcomes battery sulfation to restore reserve capacity
  • Reverse polarity protection and battery fault detection

Additional Attributes:

  • GTIN: 00010271026968
  • AC Input: Requires 20A service
  • Add-On: N/A
  • Battery Fault Detection: Yes
  • Battery Types Charged: Flooded, AGM, Spiral, Deep Cycle, Marine
  • Charging Phases: 7
  • Charging Rates: 100/40/10A
  • Maximum Voltage Ripple in PS Mode: 100mV
  • Operating Voltage: 12V
  • Operational Mode: Automatic
  • Output cable Gauge: #2AWG
  • Output Cable Length: 13'
  • Power Supply Output: 0-100A on Demand, 13.1-14.9V
  • Reverse Polarity Protection: Yes
  • Temperature Compensation: Yes
  • UPC: 10271026968
  • Warranty: 1 Year Limited
  • Weight: 25 lbs.
  • WS1: 1 Year Limited
  • WS2: TX

Extended Information:

  • Emissions : Emissions Compliance Exempt
  • Life Cycle Status: Available To Order

Packaging:

  • Quantity of Each: 1
  • Package UOM: EA
  • Dimension: 10 x 12 x 17 inches




Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top