ACDelco Professional, premium aftermarket V-Belts serve as replacement belts for today's most demanding engine drives. Due to thermal forces, these variable notched belts actually tighten on the drive as they get hot. This results in improved belt performance by reducing tension, decay, and noise. These premium aftermarket replacement v-belts are manufactured to meet your expectations for fit, form, and function. ⚠
| FAQ - Answer 1 | Yes, this may be indicative of an alignment issue or a failed tensioner. |
| FAQ - Answer 2 | Yes, you may lose your power steering or stall out. Your car is not drivable when your drive belt fails. |
| FAQ - Answer 3 | Yes, the leading causes of belt failure are improper tension and misaligned pulleys. Both these conditions cause excessive heat which leads to belt failure. Have your belts checked every 3,000 miles for belt wear, proper tension, and pulley alignment. |
| FAQ - Answer 4 | No, when the belt backing has been torn or cracked, the belt should be replaced. |
| FAQ - Answer 5 | No, use the belt in the way it's listed in the ACDelco belts and hoses catalog. |
| FAQ - Answer 6 | No, remember the leading cause of belt failure is improper tension and misaligned pulleys. Improper tension will cause the belt to slip and you may notice a loss of performance from the air conditioning system as well as increased heat under the hood. High heat can lead to premature accessory failure. |
| FAQ - Question 1 | Could an automotive belt tear during use? |
| FAQ - Question 2 | Will I know immediately if an automotive belt tears? |
| FAQ - Question 3 | Are there steps I can take to ensure a longer automotive belt life? |
| FAQ - Question 4 | Is there a way to repair a torn automotive belt? |
| FAQ - Question 5 | Can I use the same automotive belt for multiple uses? |
| FAQ - Question 6 | Will a worn automotive belt affect gas mileage? |
| Good Maintenance Practices - Section 1 - Bullet 1 | Do not use belt dressings to stop belt slippage or noise. These are oil based and may cause belt deterioration. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Never twist a belt more than 90 degrees during inspection. This may damage the tensile cords and cause premature failure. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Replace serpentine belts every 60,000 - 100,000 miles. Check vehicle's owner's manual. |
| Good Maintenance Practices - Section 1 - Bullet 4 | Replace V-belts after 3 to 4 years, or every 36,000 to 48,000 miles. |
| Good Maintenance Practices - Section 1 - Bullet 5 | Use an approved tension gauge to check belt tension. |
| Good Maintenance Practices - Section 1 - Bullet 6 | Check for proper belt tension after 500 to 1,000 miles following belt installation. Recheck often, at least twice a year or every 6,000 miles. |
| Measurements | 50 1/2 in x 46 7/8 |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Rubber Loss: (most common belt wear) a belt wear gauge measures rubber loss, which can result in reduced power transfer from the crank to the accessories. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Glazing: shiny spots can indicate a slipping belt that isn't properly transferring power to accessories. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 3 | Pilling: worn rubber can fill in grooves and cause noise, heat, vibration, and excessive wear. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 4 | Abrasion: wear along the side could indicate misalignment due to a failed tensioner. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 5 | Cracking: older neoprene belts crack as they near the end of their life cycle and often need to be replaced. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 6 | Engine stops or backfires. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 7 | The belt is producing a squealing noise. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 8 | Headlights dim while driving. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 9 | Loss of battery charge. |
DAYCO
Dayco® Top Cog® Belt is the workhorse of the heavy-duty industry. The cogs in the top of the belt deliver increased flexibility around small pulleys, and the increased surface area results in a...
ACDelco
Standard High Capacity V-BeltBRAND: ACDelcoFEATURES:A/C Compressor Belt;Air Brake Hose;Air Intake Duct Drain Hose;Alternator Decoupler Pulley;Coolant Hose;Drive Belt;Elbow Air Vent Hose;Flanged Idler...
ACDelco
Standard High Capacity V-BeltBRAND: ACDelcoFEATURES:A/C Compressor Belt;Air Brake Hose;Air Intake Duct Drain Hose;Alternator Decoupler Pulley;Coolant Hose;Drive Belt;Elbow Air Vent Hose;Flanged Idler...
ACDelco
Standard High Capacity V-BeltBRAND: ACDelcoFEATURES:A/C Compressor Belt;Air Brake Hose;Air Intake Duct Drain Hose;Alternator Decoupler Pulley;Coolant Hose;Drive Belt;Elbow Air Vent Hose;Flanged Idler...
ACDelco
ACDelco Professional, premium aftermarket V-Belts serve as replacement belts for today's most demanding engine drives. Due to thermal forces, these variable notched belts actually tighten on the...
