ACDelco
ACDelco 18B438 | Front Brake Drum
Front Brake DrumBRAND: ACDelcoFEATURES:Abs Components;Brake;Brake Caliper;Brake Caliper Lubricant;brake care;Brake Fluid;Brake Pad;Brake Parts;Brake Rotor;Brake Shoe;brakes...
ACDelco Professional Brake Drums are constructed with G3000 SAE qualified material for structural integrity and maximum service life. They are tested to ISO/TS 16949 quality system standards and validated for balance to provide better braking performance. Chamfer angle, vane configuration, and plate thickness all follow the OE design, making them a premium aftermarket replacement for your GM and non-GM vehicle. Also, no machining is required. ACDelco Professional Brake Drums are ready to be installed right out of the box. ?
ABS Sensor Ring Included | No |
Bolt Circle Diameter (in) | 4.75 |
Bolt Circle Diameter (mm) | 120.7 |
Bolt Hole Quantity | 5 |
Brake Surface Finish | Turned |
Center Bore Diameter (in) | 2.81 in |
Center Bore Diameter (mm) | 71.5 mm |
Discard Thickness (in) | 11.06 |
Discard Thickness (mm) | 280.9 |
FAQ - Answer 1 | No, but it is a good idea to inspect them for wear-out, cracking, leaking etc. |
FAQ - Answer 2 | Yes, ACDelco also offers GM OE and Advantage brake drums. |
FAQ - Answer 3 | No, but it is a good idea to inspect them at every tire rotation. |
FAQ - Question 1 | Do I have to replace all my brake parts when replacing my brake drums? |
FAQ - Question 2 | Does ACDelco offer other grades of brake drums? |
FAQ - Question 3 | Do I have to replace my brake drums after a certain amount of time? |
Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems: |
Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
Grade Type | Regular |
Height (in) | 4.2 |
Length (in) | 11.06 |
Material | Cast Iron |
Mount Hole Diameter (in) | 0.453 in |
Mount Hole Diameter (mm) | 11.506 mm |
Outer Cooling Fins | No |
Programming Required | No |
Signs of Wear & Troubleshooting - Section 1 - Bullet 4 | Squealing or scraping noises. |
Signs of Wear & Troubleshooting - Section 1 - Bullet 5 | Brake pedal pulsation (not to be confused with normal ABS operation). |
Weight (lb) | 15 |
Width (in) | 13 |