ACDelco
ACDelco 19330485 | Steering Gear
ACDelco GM Original Equipment Remanufactured Steering Gears convert steering wheel rotation into the side-to-side motion needed to steer your vehicle's front wheels, and are GM-recommended...
ACDelco GM Original Equipment Remanufactured Steering Gears convert steering wheel rotation into the side-to-side motion needed to steer your vehicle's front wheels, and are GM-recommended replacements for your vehicle's original components. Remanufacturing steering gears is an industry standard practice that involves disassembly of existing units, and replacing components that are most prone to wear and failure with new components. Damaged and obsolete parts are replaced and are end of line tested to ensure they perform to ACDelco specifications. In addition, remanufacturing helps return components back into service rather than processing as scrap or simply disposing of them. These steering gears will provide the same performance, durability, and service life you expect from ACDelco. ?
FAQ - Answer 1 | Yes. Hydraulic power steering systems use a pump to send pressurized fluid to the hydraulic steering gear, where pressurized fluid assists the driver to move the steering gear. Electric power steering systems do not use fluid; instead, they use an electric motor and sensors to move the steering gear. |
FAQ - Answer 2 | Yes. If there is a power steering pump mounted to your vehicle's engine, or your owner's manual calls for power steering fluid, then your vehicle uses a hydraulic power steering system. If your vehicle's engine does not have a power steering pump or your owner's manual indicates your vehicle does not require power steering fluid, then your vehicle uses an electric power steering system. |
FAQ - Answer 3 | Yes. Uneven tire wear, vehicle pull, or an off center steering wheel may indicate that your vehicle requires an alignment. |
FAQ - Answer 4 | Yes. You will be able to steer your vehicle if the power steering goes out for both hydraulic and electric power steering systems. It will require more effort, especially at lower speeds. If your vehicle has electric power steering, a 'service steering system' light will likely be apparent before it is realized that the power assist is off. If your power steering goes out, have the system inspected and repaired as soon as possible. |
FAQ - Question 1 | Is there a difference between a hydraulic and an electric power steering system? |
FAQ - Question 2 | Can I tell if my vehicle uses an electric or a hydraulic power steering system? |
FAQ - Question 3 | Are there signs that can indicate my vehicle needs an alignment? |
FAQ - Question 4 | Will I be able to steer my vehicle if my power steering goes out? |
Good Maintenance Practices - Section 1 - Bullet 1 | Unusual noise when turning the steering wheel |
Good Maintenance Practices - Section 1 - Bullet 2 | A shimmy or shake in the steering wheel |
Good Maintenance Practices - Section 1 - Bullet 3 | Heavy or unresponsive steering at low speeds or during parking lot maneuvers |
Good Maintenance Practices - Section 1 - Bullet 4 | Steering wheel not returning to 'center' properly |
Good Maintenance Practices - Section 1 - Bullet 5 | Service power steering system light illuminating in the driver information center |
Good Maintenance Practices - Section 1 - Header | Have your vehicle inspected if it exhibits any of the following symptoms: |
Good Maintenance Practices - Section 2 - Bullet 1 | Check your power steering fluid levels and belts and hoses. |
Good Maintenance Practices - Section 2 - Bullet 2 | Wet spots/fluid stains on the ground beneath the vehicle. |
Good Maintenance Practices - Section 2 - Header | For hydraulic power steering systems: |
Good Maintenance Practices - Section 3 - Bullet 1 | Especially have the inner and outer tie rods inspected for grease leaks and excessive lash or 'play' |
Good Maintenance Practices - Section 3 - Header | If you live in areas that experience harsh winter weather, have the entire steering system inspected before winter arrives. |
Height (in) | 8.25 |
Length (in) | 15.12 |
Meets or Exceeds Original Equipment Manufacture Specifications | Yes |
Output Shaft Spline Quantity | 32 |
Power Assisted | Yes |
Programming Required | No |
Total Turns Lock To Lock | 3 |
Weight (lb) | 27.2 |
Width (in) | 11.75 |