×
close
click to zoom in

ACDelco 25620213 | Brake Hydraulic Line

(No reviews yet) Write a Review
$49.99
Part Number
ACD25620213
UPC:
808709022565
Condition:
New
5 customers are viewing this product

ACDelco GM Original Equipment Brake Hydraulic Lines are quality reinforced lines that carry fluid within the brake system, and are GM-recommended replacements for your vehicle's original components. The hydraulic fluid must travel to the wheel brakes from the master cylinder. It does this through brake lines or pipes and brake hoses. Brake lines and hoses are designed to withstand high pressures, and these brake hydraulic lines have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ⚠ WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

BRAND: ACDelco

FEATURES:

  • Brake Pressure Modulator Valve Rear Hydraulic Pipe Assembly
  • Buick;Oldsmobile;Pontiac
  • GM-recommended replacement part for your GM vehicle's original factory component
  • hydraulic-line;stainless-steel-line;stainless-steel-brake-line;copper-brake-line;dot-3;dot-4;brake-system-lines;brake-hardline;brake-hydrualic-line;break
  • Manufactured with GM Original Equipment specification for fit, form, and function
  • Offering the quality, reliability, and durability of GM OE

SPECIFICS:

Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
Height (in)4
Length (in)25.2
Meets or Exceeds Original Equipment Manufacture SpecificationsYes
Programming RequiredNo
Signs of Wear & Troubleshooting - Section 1 - Bullet 1Brake pedal pulsation (not to be confused with normal ABS operation).
Signs of Wear & Troubleshooting - Section 1 - Bullet 2Vehicle pulls to the left or right when brakes are applied.
Weight (lb)0.3
Width (in)12

EXCEPT ELEC TRACTION CONT(NW9)

APPLICATIONS:

  • 1997-1998 Oldsmobile Regency - Position: Front At Master Cylinder
  • 1996-1996 Buick Park Avenue - Position: Front At Master Cylinder
  • 1996-1999 Pontiac Bonneville - Position: Front At Master Cylinder
  • 1996-1999 Oldsmobile 88 - Position: Front At Master Cylinder
  • 1996-1996 Oldsmobile 98 - Position: Front At Master Cylinder
  • 1996-1999 Oldsmobile LSS - Position: Front At Master Cylinder
  • 1996-1999 Buick LeSabre - Position: Front At Master Cylinder

Product type:
Aftermarket
Product Description:
Brake Pressure Modulator Valve Rear Hydraulic Pipe Assembly
Programming Required:
No
End 2 Thread Diameter (Inch):
0.47
End 1 Thread Diameter (Inch):
0.47
Fitting Material:
Steel
Fitting Type:
Flared Tube Nuts
End 1 Thread Diameter (Millimeter):
12
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
Offering the quality, reliability, and durability of GM OE
Features & Benefits - Bullet 3:
Manufactured with GM Original Equipment specification for fit, form, and function
Features & Benefits - Bullet 1:
GM-recommended replacement part for your GM vehicle's original factory component
Weight (lb) (Pound):
0.3
Height (in) (Inch):
4
Width (in) (Inch):
12
Length (in) (Inch):
25.2
Signs of Wear & Troubleshooting - Section 1 - Bull:
Vehicle pulls to the left or right when brakes are applied.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Brake pedal pulsation (not to be confused with normal ABS operation).
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Life Cycle Status:
Announced
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Life Cycle Status Description:
Announced - Part has been announced to customers on a paper “New Number Announcement”. Part is active.
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Item Level GTIN:
00808709022565
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Meets or Exceeds Original Equipment Manufacture Sp:
Yes
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Teflon Lined:
No
End 2 Thread Diameter (Millimeter):
12
End 1 Flare Type:
Bubble
End 2 Flare Type:
Bubble
Line Diameter (Inch):
0.24
Line Diameter (Millimeter):
6
Line Length (Inch):
40.08
Line Length (Millimeter):
1018
Bendable:
No
Outer Spring:
No
Polyvinyl Fluoride Coated:
No
Outer Wear Guard:
No
Pre-Formed:
Yes
Line Material:
Steel and Rubber
Fitting Finish:
Zinc Chromate
Country of Origin:
United States
Weight - Each (Gross Pounds):
00.30
Height - Each (Inch):
04.00
Length - Each (Inch):
25.20
Width - Each (Inch):
12.00



Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top