ACDelco Professional, premium aftermarket Dual-Sided V-Ribbed Belts are ideal for replacing original equipment belts on serpentine drives that require a higher degree of efficiency when transmitting power. They are designed for small diameter pulleys and for use with or without automatic tensioners. These premium aftermarket replacement dual-sided v-ribbed belts are manufactured to meet your expectations for fit, form, and function.
| ACD_RemanDes | No |
| AltPA_1040_mm | 20 |
| AltPA_2002_mm | 1843 |
| AltPA_2005_mm | 1872 |
| FAQ - A1 | Yes, this may be indicative of an alignment issue or a failed tensioner. |
| FAQ - A2 | Yes, you may lose your power steering or stall out. Your car is not drivable when your drive belt fails. |
| FAQ - A3 | Yes, the leading causes of belt failure are improper tension and misaligned pulleys. Both these conditions cause excessive heat which leads to belt failure. Have your belts checked every 3,000 miles for belt wear, proper tension, and pulley alignment. |
| FAQ - A4 | No, when the belt backing has been torn or cracked, the belt should be replaced. |
| FAQ - A5 | No, use the belt in the way it's listed in the ACDelco belts and hoses catalog. |
| FAQ - A6 | No, remember the leading cause of belt failure is improper tension and misaligned pulleys. Improper tension will cause the belt to slip and you may notice a loss of performance from the air conditioning system as well as increased heat under the hood. High heat can lead to premature accessory failure. |
| FAQ - Q1 | Could an automotive belt tear during use? |
| FAQ - Q2 | Will I know immediately if an automotive belt tears? |
| FAQ - Q3 | Are there steps I can take to ensure a longer automotive belt life? |
| FAQ - Q4 | Is there a way to repair a torn automotive belt? |
| FAQ - Q5 | Can I use the same automotive belt for multiple uses? |
| FAQ - Q6 | Will a worn automotive belt affect gas mileage? |
| Good Maintenance Practices - S1 B1 | Do not use belt dressings to stop belt slippage or noise. These are oil based and may cause belt deterioration. |
| Good Maintenance Practices - S1 B2 | Never twist a belt more than 90 degrees during inspection. This may damage the tensile cords and cause premature failure. |
| Good Maintenance Practices - S1 B3 | Replace serpentine belts every 60,000 - 100,000 miles. Check vehicle's owner's manual. |
| Good Maintenance Practices - S1 B4 | Replace V-belts after 3 to 4 years, or every 36,000 to 48,000 miles. |
| Good Maintenance Practices - S1 B5 | Use an approved tension gauge to check belt tension. |
| Good Maintenance Practices - S1 B6 | Check for proper belt tension after 500 to 1,000 miles following belt installation. Recheck often, at least twice a year or every 6,000 miles. |
| Marketing Statement - Product Line | Built to meet the latest demands, ACDelco's Belts and Hoses line includes automotive belts and hoses, tensioners, pulleys, and kits. ACDelco offers a wide variety of Professional premium, aftermarket parts, and a select offering of GM Original Equipment Belts that fit a variety of vehicles on the road today. |
| Marketing Statement - Sub Brand | When it comes to replacing your Belts, ACDelco offers a full line of Professional, premium aftermarket Belt products. To help make part replacement simple and precise, ACDelco also offers pulleys, tensioners, and kits. ACDelco Professional, premium aftermarket belts fit both GM and Non GM vehicles. |
| Measurements | 13/16 in x 73 3/4 in |
| Mkt_BrandQual_Name | Dual Sided |
| Mkt_State_Warranty_CA | Limited Lifetime Warranty as long as original purchaser still owns vehicle (Parts Only). |
| Mkt_State_Warranty_US | Limited Lifetime as long as original purchaser owns vehicle. (Parts Only) |
| Signs of Wear & Troubleshooting - S1 B1 | Rubber Loss: (most common belt wear) a belt wear gauge measures rubber loss, which can result in reduced power transfer from the crank to the accessories. |
| Signs of Wear & Troubleshooting - S1 B2 | Glazing: shiny spots can indicate a slipping belt that isn't properly transferring power to accessories. |
| Signs of Wear & Troubleshooting - S1 B3 | Pilling: worn rubber can fill in grooves and cause noise, heat, vibration, and excessive wear. |
| Signs of Wear & Troubleshooting - S1 B4 | Abrasion: wear along the side could indicate misalignment due to a failed tensioner. |
| Signs of Wear & Troubleshooting - S1 B5 | Cracking: older neoprene belts crack as they near the end of their life cycle and often need to be replaced. |
| Signs of Wear & Troubleshooting - S1 B6 | Engine stops or backfires. |
| Signs of Wear & Troubleshooting - S1 B7 | The belt is producing a squealing noise. |
| Signs of Wear & Troubleshooting - S1 B8 | Headlights dim while driving. |
| Signs of Wear & Troubleshooting - S1 B9 | Loss of battery charge. |
| Vintage_Part_Indicator | N |
ACDelco
ACDelco Specialty Heavy Duty V-Belts have a patented EPDM rubber construction that helps provides peak performance at extreme, prolonged operating temperatures and a distinct, green gum stock built...
ACDelco
ACDelco GM Original Equipment Serpentine Belts are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These serpentine belts allows for the operation of various...
ACDelco
ACDelco Professional, premium aftermarket V-Ribbed Advanced Technology Belts serve as replacement belts for accessory belt drive systems (ABDS) and other serpentine belt applications. They are...
ACDelco
ACDelco GM Original Equipment Serpentine Belts are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These serpentine belts allows for the operation of various...
ACDelco
ACDelco GM Original Equipment Serpentine Belts are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These serpentine belts allows for the operation of various...
