×
close

Shopping Cart:

Toggle menu
1-321-400-8080

24/7 Customer Service
0

$0.00

0
ACDelco 177-0911 | Cadillac SRX Rear Disc Brake Rotor
click to zoom in

ACDelco 177-0911 | Cadillac SRX Rear Disc Brake Rotor

(No reviews yet) Write a Review
$101.99
Part Number
ACD177-0911
UPC:
808709275480
Condition:
New
5 customers are viewing this product

video gallery

Description

ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are GM-recommended replacements for your vehicle's original components. These disc brake rotors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

BRAND: ACDelco

FEATURES:

  • Cadillac
  • GM-recommended replacement part for your GM vehicle's original factory component
  • Inspected for balance, resulting in smooth brake operation and noise reduction
  • Manufactured to GM OE specification for fit, form, and function
  • Offering the quality, reliability, and durability of GM OE

SPECIFICS:

ABS Sensor Ring IncludedNo
Bolt Circle Diameter (in)4.528
Bolt Circle Diameter (mm)115
Bolt Hole Quantity6
Center Bore Diameter (in)2.8 in
Center Bore Diameter (mm)70.7 mm
ConstructionFull Cast
Disc FinishCoated
Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
Grade TypePerformance
Hat FinishPlain
Height (in)1.9
Height (mm)47.9
Length (in)15.1
MaterialCast Iron
Programming RequiredNo
Rust Resistant CoatingYes
Signs of Wear & Troubleshooting - Section 1 - Bullet 1Vehicle pulls to the left or right when brakes are applied.
Signs of Wear & Troubleshooting - Section 1 - Bullet 2Visible ridges or deep grooves on the rotor surface.
SlottedNo
Solid Or Vented Type RotorVented
Surface TypeSmooth
Weight (lb)22.15
Width (in)14.3

DOWNLOADS:

APPLICATIONS:

  • 2004-2009 Cadillac SRX - Position: Rear

Attributes
Product type:
Aftermarket
Brand Description:
Rear Brake Rotor
Product Description:
Rear Disc Brake Rotor
ABS Tone Ring Included:
No
Grade Type:
Performance
Bolt Hole Quantity:
6
Nominal Thickness (Inch):
1.024
Outside Diameter (Inch):
12.6
Discard Thickness (Inch):
0.945
Rust Resistant Coating:
Yes
Construction:
Full Cast
Material:
Cast Iron
Slotted:
No
Solid Or Vented Type Rotor:
Vented
Surface Type:
Smooth
Hat Finish:
Bare
Disc Finish:
Coated
Programming Required:
No
Pad Contact Surface Width (Inch):
1.4
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
GM-recommended replacement part for your GM vehicle's original factory component
Life Cycle Status:
Announced
Features & Benefits - Bullet 4:
Manufactured to GM OE specification for fit, form, and function
Life Cycle Status Description:
Announced - Part has been announced to customers on a paper “New Number Announcement”. Part is active.
Features & Benefits - Bullet 3:
Offering the quality, reliability, and durability of GM OE
Item Level GTIN:
00808709275480
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Weight (lb) (Pound):
22.15
Height (in) (Inch):
1.9
Width (in) (Inch):
14.3
Length (in) (Inch):
15.1
Signs of Wear & Troubleshooting - Section 1 - Bull:
Visible ridges or deep grooves on the rotor surface.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Vehicle pulls to the left or right when brakes are applied.
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Outside Diameter (Millimeter):
320
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Height (mm) (Millimeter):
47.9
Bolt Circle Diameter (in) (Inch):
4.528
Bolt Circle Diameter (mm) (Millimeter):
115
Discard Thickness (Millimeter):
24
Nominal Thickness (Millimeter):
26
Pad Contact Surface Width (Millimeter):
36.6
Center Hole Diameter (Millimeter):
71
Center Hole Diameter (Inch):
2.8
Country of Origin:
United States
Weight - Each (Gross Pounds):
22.15
Height - Each (Inch):
03.62
Length - Each (Inch):
15.12
Width - Each (Inch):
14.50



Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top