Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE¨ New Master Cylinders to match O.E. performance. Supplied with new O.E.-quality seals and cups, each unit is endurance-tested to ensure perfect fit, function and reliable performance.
| Bore Diameter (N) | 1.181" |
| E-Waste | No |
| FAQs | Check booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder. |
| FAQs | Does a step bore style master cylinder require a specific bleeding process? |
| FAQs | Dot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid. |
| FAQs | How can I test a master cylinder to see if it's bypassing? |
| FAQs | Most likely, the fluid in the system is contaminated. The most common form of contamination occurs when petroleum-based fluid has been accidentally introduced into the brake system. If that has happened it is almost certain that all rubber components in the brake system (hoses, seals, bladders) will need to be replaced after the system is thoroughly flushed. If the contamination is due to moisture, rust and/or dirt, it might be possible to restore operation by flushing the system and replacing the brake fluid with fresh, clean fluid. Always use the manufacturer-recommended brake fluid from a sealed container. |
| FAQs | Simply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK. |
| FAQs | What causes the car to pull to one side during braking? |
| FAQs | What causes the brakes to lock up after only a couple of miles? |
| FAQs | Why is the piston stuck inside the bore of my master cylinder? |
| FAQs | Check the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure. |
| FAQs | First, check for air in the system. Make sure master cylinder is level when bleeding. Air will compress in a hydraulic system causing a low pedal. Then, check for brake hose swelling or expanding under pressure. Next, check brake drums/discs for proper specifications. Finally, check brake material. |
| FAQs | My original master cylinder leaked out of the back of the piston into the booster area. Why? |
| FAQs | The first step to bench bleeding a step bore is to slowly depress the master cylinder piston, then release slowly and wait 20 seconds before depressing again. NEVER pump piston/pedal with a step bore style master cylinder. Follow the same process on the vehicle. |
| FAQs | The master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper. |
| FAQs | This is caused by a problem with the caliper or a brake hose. |
| FAQs | Whatâs the difference between Dot 3, 4 and 5? |
| FAQs | As a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container. |
| FAQs | I replaced the master cylinder and now the pedal is high and hard. Why? |
| FAQs | One side of my front brakes wonât release, why? |
| FAQs | Replace all brake fluid. Brake fluid is hygroscopic which means it absorbs moisture. Too much water in brake fluid will cause vapor lock and apply pressure to the wheels. Also check for proper push rod adjustments and stop light/cruise control switch adjustments. |
| FAQs | The brake pedal is low and spongy. Is it a bad master cylinder? |
| FAQs | What type of fluid should I use: DOT 3, DOT 4 or DOT 5? |
| Features and Benefits | Castings feature a premium protective coating to minimize corrosion and extend unit life |
| Features and Benefits | Only O.E.-quality seals and cups are used to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications |
| Features and Benefits | Mounting hardware and bleeding kits are supplied with every unit to make the installation and bleeding process faster and easier (where applicable) |
| Features and Benefits | Plastic reservoirs are vacuum-tested to ensure they are leak free |
| Features and Benefits | Seals are temperature-cycled from -30°F to +220°F to ensure reliable performance during your daily commute |
| Features and Benefits | Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure |
| Installation Hardware Included | No |
| Master Cylinder Color/Finish | Gray |
| Master Cylinder Material | Cast Iron |
| Mounting Hole Quantity | 2 |
| Package Contents | Master Cylinder |
| Pedal Rod Included | No |
| Port Quantity | 2 |
| Primary Port Size | 9/16 x 18 |
| Product Condition | New |
| Reservoir Included | Yes |
| Reservoir Material | Cast Iron |
| Reservoir Type | Integral |
| Secondary Port Size | 1/2 x 20 |
Cardone Industries
CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting...
Cardone Industries
Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE® New Master Cylinders to match O.E. performance...
Cardone Industries
Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE® New Master Cylinders to match O.E. performance...
Cardone Industries
Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE¨ New Master Cylinders to match O.E. performance...
Cardone Industries
Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE¨ New Master Cylinders to match O.E. performance...
