CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
| Connector Quantity | 4 |
| Connector Shape | Rectangle |
| E-Waste | Yes |
| FAQs | No, not all Ford vehicles require a PATS reset. Check the PATS chart found on the MotorCraft Site for your application. |
| FAQs | The wrong ECM may have been installed. Verify the Ford Engineering Id number, found on the ECM/PCM, crosses to the correct CARDONE number. |
| FAQs | Do all Ford vehicles require a Passive Anti Theft System (P.A.T.S) reset? |
| FAQs | I replaced the PCM in my GM vehicle. Do I need to reset the Passlock or Passkey Vehicle Anti Theft System (VATS)? |
| FAQs | Do all Chrysler Power Train Control Modules (PCM) need vin programming? |
| FAQs | The replacement ECM for a Ford vehicle won’t start the vehicle. Why? |
| FAQs | Yes, there's a 10 minute procedure utilizing a Tech 2 Scanner and a GM Terminal Subscription. There is also a 30 minute manual procedure that can be done without a scanner. Refer to an OE approved service manual for either option. |
| FAQs | Chrysler PCM's identified with a "V" suffix will need to be vin programmed. |
| FAQs | Prior to replacing the original ECM/PCM, the installer should determine what caused the original to fail. Common areas that cause failures are: poor grounds and powers, bad wiring harness, shorted solenoids/relays. |
| FAQs | What steps should I take to assure the original ecm/pcm is causing the issue? |
| Features and Benefits | Re-soldering of critical components ensures superior electrical connections. This prevents intermittent failures and leads to longer product life. |
| Features and Benefits | Tested with automated, computerized equipment or bench-tested, depending on application, to ensure functionality. |
| Features and Benefits | On-car vehicle validation is done to test durability and performance. |
| Features and Benefits | Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%. |
| Features and Benefits | As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit. |
| Flash Programming Required | Yes |
| Flashable | No |
| Housing Material | Aluminum |
| Mounting Hardware Included | No |
| Mounting Hole Quantity | 3 |
| Product Condition | Remanufactured |
| Removable PROM | No |
| Terminal Quantity | 38;38;38,38 |
| Terminal Type | Pin|Male; Pin|Male; Pin|Male; Pin Male |
Cardone Industries
CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed,...
Cardone Industries
CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed,...
Cardone Industries
CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed,...
Cardone Industries
CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed,...
Cardone Industries
CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed,...
