×
close
click to zoom in

GM Genuine Parts 177-1211 | Disc Brake Rotor

(No reviews yet) Write a Review
$99.89
Part Number
ACD177-1211
UPC:
808709696971
Condition:
New
5 customers are viewing this product

GM Genuine Parts Disc Brake Rotors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE). ⚠ WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

BRAND: GM Genuine Parts

FEATURES:

  • brake-pad;-brake-shoe;rotors;drum;brake-job;front-brake;rear-brake;cylider;hydraluic;dot-3;dot-4;front-brakes;rear-brakes;brake-set;breaks
  • Chevrolet
  • Front Brake Rotor
  • Front Disc Brake Rotor
  • GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
  • GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
  • GM regularly updates production and service part designs to integrate new materials and technologies
  • Inspected for balance, resulting in smooth brake operation and noise reduction
  • Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)

SPECIFICS:

Bolt Circle Diameter (in)4.134
Bolt Circle Diameter (mm)105
Bolt Hole Quantity5
Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
Height (in)1.8
Height (mm)45.5
Length (in)10.9
Lug Quantity5
Original Equipment ReplacementYes
Programming RequiredNo
Signs of Wear & Troubleshooting - Section 1 - Bullet 1Brake pedal pulsation (not to be confused with normal ABS operation).
Signs of Wear & Troubleshooting - Section 1 - Bullet 2Squealing or grinding noises.
Signs of Wear & Troubleshooting - Section 1 - Bullet 3Low brake pedal height.
Signs of Wear & Troubleshooting - Section 1 - Bullet 4Vehicle pulls to the left or right when brakes are applied.
Signs of Wear & Troubleshooting - Section 1 - Bullet 5Visible ridges or deep grooves on the rotor surface.
Signs of Wear & Troubleshooting - Section 1 - HeaderBrake rotor signs of wear include:
SlottedNo
Weight (lb)13.86
Width (in)10.9

Product type:
Aftermarket
Brand Description:
Front Brake Rotor
Product Description:
Front Disc Brake Rotor
ABS Tone Ring Included:
No
Grade Type:
Regular
Bolt Hole Quantity:
5
Nominal Thickness (Inch):
1.024
Outside Diameter (Inch):
10.827
Rust Resistant Coating:
Yes
Construction:
Composite
Material:
Gray Cast Iron
Slotted:
No
Solid Or Vented Type Rotor:
Vented
Surface Type:
Smooth
Lug Quantity:
5
Inside Diameter (Inch):
5.472
Programming Required:
No
Pad Contact Surface Width (Inch):
2.141
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
Features & Benefits - Bullet 4:
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Life Cycle Status:
Proposed
Features & Benefits - Bullet 3:
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Item Level GTIN:
00808709696971
Weight (lb) (Pound):
13.86
Height (in) (Inch):
1.8
Width (in) (Inch):
10.9
Length (in) (Inch):
10.9
Signs of Wear & Troubleshooting - Section 1 - Bull:
Visible ridges or deep grooves on the rotor surface.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Vehicle pulls to the left or right when brakes are applied.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Squealing or grinding noises.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Brake pedal pulsation (not to be confused with normal ABS operation).
Signs of Wear & Troubleshooting - Section 1 - Bull:
Low brake pedal height.
Signs of Wear & Troubleshooting - Section 1 - Head:
Brake rotor signs of wear include:
Features & Benefits - Bullet 5:
GM regularly updates production and service part designs to integrate new materials and technologies
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Original Equipment Replacement:
Yes
Inside Diameter (Millimeter):
139
Outside Diameter (Millimeter):
275
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Height (mm) (Millimeter):
45.5
Bolt Circle Diameter (in) (Inch):
4.134
Bolt Circle Diameter (mm) (Millimeter):
105
Nominal Thickness (Millimeter):
26
Pad Contact Surface Width (Millimeter):
54.39
Country of Origin:
Mexico
Weight - Each (Gross Pounds):
13.87
Height - Each (Inch):
03.30
Length - Each (Inch):
13.10
Width - Each (Inch):
12.30



Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top