×
close

Shopping Cart:

Toggle menu
1-321-400-8080

24/7 Customer Service
0

$0.00

0
ACDelco 177-0947 | Rear Brake Drum
click to zoom in

ACDelco 177-0947 | Rear Brake Drum

(No reviews yet) Write a Review
$97.19
Part Number
ACD177-0947
UPC:
00707773292426
Condition:
New
5 customers are viewing this product

video gallery

Description
ACDelco GM Original Equipment Brake Drums are cylinder shaped bowls where the wheel cylinder presses the brake shoes outward against the inside of the drum. Drums are typically found on older vehicles and on the rear axles of trucks and some cars. These original equipment brake drums are manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

BRAND: ACDelco

FEATURES:

  • Chevrolet;Pontiac;Saturn
  • GM-recommended replacement part for your GM vehicle's original factory component
  • Have a rust-preventative coating to help protect against corrosion
  • Inspected for balance, resulting in smooth brake operation and noise reduction
  • Manufactured to GM OE specification for fit, form, and function
  • Offering the quality, reliability, and durability of GM OE

SPECIFICS:

Bolt Circle Diameter (in)3.937008
Bolt Circle Diameter (mm)100
Bolt Hole Quantity4
Drum Center Bore Diameter (in)2.246457
Drum Center Bore Diameter (mm)57.06
Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
Height (in)3.38
Length (in)13.12
MaterialCast Iron
Mount Hole Diameter (in)0.5511811 in
Mount Hole Diameter (mm)14 mm
Programming RequiredNo
Signs of Wear & Troubleshooting - Section 1 - Bullet 1Squealing or scraping noises.
Signs of Wear & Troubleshooting - Section 1 - Bullet 2Brake pedal pulsation (not to be confused with normal ABS operation).
Weight (lb)11.29
Width (in)12.38

DOWNLOADS:

APPLICATIONS:

  • 2007-2007 Chevrolet Cobalt - Position: Rear
    • STEEL WHL(PG1)
  • 2008-2008 Chevrolet Cobalt - Position: Rear
    • SOFT RIDE SUSP(FE1), ALUM WHL(PFD), STEEL WHL(PG1)
  • 2005-2006 Pontiac Pursuit - Position: Rear
    • SOFT RIDE SUSP(FE1), Cast Iron
  • 2007-2007 Pontiac G5 - Position: Rear
    • STEEL WHL(PG1)
  • 2005-2008 Chevrolet Cobalt - Position: Rear
    • SOFT RIDE SUSP(FE1), Cast Iron
  • 2003-2007 Saturn Ion - Position: Rear
  • 2007-2008 Pontiac G5 - Position: Rear
    • SOFT RIDE SUSP(FE1), Cast Iron
  • 2008-2008 Pontiac G5 - Position: Rear
    • SOFT RIDE SUSP(FE1), ALUM WHL(PFD), STEEL WHL(PG1)
Warranty Information
1-year Replacement unlimited-mileage warranty
Attributes
Part Type:
Aftermarket
Brand Description:
Rear Brake Drum
Bolt Hole Quantity:
4
Outside Diameter (Inch):
10.66929
Material:
Cast Iron
Inside Diameter (Inch):
9.059843
Programming Required:
No
Maximum Brake Diameter (Discard) (Inch):
9.094
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
Have a rust-preventative coating to help protect against corrosion
Features & Benefits - Bullet 4:
Offering the quality, reliability, and durability of GM OE
Features & Benefits - Bullet 3:
GM-recommended replacement part for your GM vehicle's original factory component
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Weight (lb) (Pound):
11.29
Height (in) (Inch):
3.38
Width (in) (Inch):
12.38
Length (in) (Inch):
13.12
Signs of Wear & Troubleshooting - Section 1 - Bull:
Squealing or scraping noises.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Brake pedal pulsation (not to be confused with normal ABS operation).
Features & Benefits - Bullet 5:
Manufactured to GM OE specification for fit, form, and function
Life Cycle Status:
Announced
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Life Cycle Status Description:
Announced - Part has been announced to customers on a paper “New Number Announcement”. Part is active.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Item Level GTIN:
00707773292426
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Inside Diameter (Millimeter):
230.12
Outside Diameter (Millimeter):
271
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Mount Hole Diameter (in):
0.5511811 in
Mount Hole Diameter (mm):
14 mm
Bolt Circle Diameter (in) (Inch):
3.937008
Bolt Circle Diameter (mm) (Millimeter):
100
Maximum Brake Diameter (Discard) (Millimeter):
231
Drum Center Bore Diameter (in) (Inch):
2.246457
Drum Center Bore Diameter (mm) (Millimeter):
57.06
Country of Origin:
United States
Weight - Each (Gross Pounds):
11.29
Height - Each (Inch):
03.38
Length - Each (Inch):
13.12
Width - Each (Inch):
12.38



Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top