| Adjustable | No |
| Ball Joint Assembly | Yes |
| Castle Nut Included | Yes |
| Cotter Pin Hole | Yes |
| Dust Boot Included | Yes |
| FAQ - Answer 1 | Yes. ACDelco Advantage Chassis parts are for both GM and non-GM vehicle applications. |
| FAQ - Answer 2 | Yes. You should replace your ball joints as a set to make front end alignment easier. |
| FAQ - Answer 3 | Yes. Installing new ball joints can interfere with the alignment of your vehicle, so a full four-wheel vehicle alignment is recommended following ball joint replacement. |
| FAQ - Question 1 | Can I use ACDelco Advantage Chassis parts on my non-GM vehicle? |
| FAQ - Question 2 | Should I replace my ball joints as a set? |
| FAQ - Question 3 | Should I perform a vehicle alignment after installing ball joints? |
| Good Maintenance Practices - Section 1 - Bullet 1 | Inspect or have your ball joints inspected for signs of wear. Over time, lubrication inside the ball joint can dry out, leading to joint wear. Even sealed ball joints can be exposed to air, and if the ball joint's protective boot is damaged, dirt and debris could further harm the function and life of the joint. Exposure to harsh driving conditions like pot holes, bumpy road surfaces, or road salt may also cause ball joints to fail. Worn ball joints could result loss of vehicle control or tire damage. Inspect your ball joints regularly, following exposure to events that may harm the component, or when you experience signs of ball joint wear. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Use new components during installation. If you replace your vehicle's ball joints, make sure to use new mounting hardware, rather than reusing the old. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Avoid replacing only one ball joint at a time. If you choose to replace a ball joint, you should consider replacing ball joints as a set to make alignment easier. |
| Good Maintenance Practices - Section 1 - Bullet 4 | Installing a new ball joint can interfere with the alignment of your vehicle. Perform a full four-wheel vehicle alignment after any ball joint replacement. |
| Greasable | Yes |
| Length (in) | 5.3 |
| Material | Steel |
| Meets or Exceeds Original Equipment Manufacture Specifications | Yes |
| Mounting Hole Quantity | 0 |
| Mounting Type | Press In |
| Programming Required | No |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Unexpected noises: a squeaking noise when your vehicle accelerates, hits a bump, or stops may indicate worn ball joints. Noises that the ball joint makes as it begins to wear can start as minor clicks felt in the steering wheel, and gradually progress to loud thumping and clunking noises as wear worsens. These sounds are particularly obvious when your vehicle shifts its weight to and from the wheel with the bad ball joint, such as when driving over a pothole. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Unexpected vibration: vibrations at higher vehicle speeds may indicate worn ball joints. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 3 | Loose or stiff steering: difficulty steering and handling your vehicle may indicate worn ball joints. If steering feels loose or sloppy, then the ball joint and socket may be wearing out together, the ball joint becoming smaller and the socket gap increasing. However, worn ball joints may also lead to tight or stiff steering, making it difficult to turn quickly and smoothly. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 4 | Tire wear: as ball joints wear, they allow the front wheels of your vehicle to point outward and away from each other in a 'toe-out' position. This position will result in uneven wear on one side of your tire that feathers across the tread toward its center. Worn ball joints may also be signaled by a more extreme variation of uneven tire wear, called camber wear, where the tire leans in or out at the top, and a hard line of excess wear is seen along one edge of your vehicle's tire. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 5 | Alignment issues: an inability to set your vehicle's alignment to proper specifications may be a sign of ball joint wear. |
| Stud Type | Threaded |
| Suspension Grade Type | Standard |
| Type | Press In |
| Weight (lb) | 1.8 |
| Width (in) | 4.9 |
ACDelco
Front Lower Suspension Ball Joint AssemblyBRAND: ACDelcoFEATURES:alignment camber kit;alignment caster kit;ball joint bearing;ball joint bolt;ball joint;bushing;center link;center link...
ACDelco
An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a...
ACDelco
An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a...
ACDelco
An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a...
ACDelco
An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a...
