ACDelco
ACDelco 177-0958 | Rear Disc Brake Rotor
$234.59
Disc Brake Rotor Rear/Front ACDelco GM Original Equipment 177-0958
click to zoom in
ACDelco 177-0992 | Rear Disc Brake Rotor
5 customers are viewing this product
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are GM-recommended replacements for your vehicle's original components. These disc brake rotors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov
BRAND: ACDelco
FEATURES:
- Buick;Chevrolet;Pontiac;Saturn
- GM-recommended replacement part for your GM vehicle's original factory component
- Inspected for balance, resulting in smooth brake operation and noise reduction
- Manufactured to GM OE specification for fit, form, and function
- Offering the quality, reliability, and durability of GM OE
SPECIFICS:
| ABS Sensor Ring Included | No |
| Bolt Circle Diameter (in) | 4.528 |
| Bolt Circle Diameter (mm) | 115 |
| Bolt Hole Quantity | 6 |
| Center Bore Diameter (in) | 2.8 in |
| Center Bore Diameter (mm) | 70.7 mm |
| Construction | Full Cast |
| Disc Finish | Coated |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Grade Type | Performance |
| Hat Finish | Plain |
| Height (in) | 1.5 |
| Height (mm) | 37 |
| Material | Cast Iron |
| Programming Required | No |
| Rust Resistant Coating | Yes |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Vehicle pulls to the left or right when brakes are applied. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Visible ridges or deep grooves on the rotor surface. |
| Slotted | No |
| Solid Or Vented Type Rotor | Solid |
| Surface Type | Smooth |
DOWNLOADS:
APPLICATIONS:
- 2006-2009 Chevrolet Uplander - Position: Rear
- SOFT RIDE SUSP(FE1), RIDE & HANDLING SUSP(FE2), SPORT SUSPENSION(FE3)
- 2006-2009 Pontiac Montana - Position: Rear
- SOFT RIDE SUSP(FE1), RIDE & HANDLING SUSP(FE2), SPORT SUSPENSION(FE3)
- 2006-2007 Buick Terraza - Position: Rear
- SOFT RIDE SUSP(FE1), RIDE & HANDLING SUSP(FE2), SPORT SUSPENSION(FE3)
- 2006-2007 Saturn Relay - Position: Rear
- SOFT RIDE SUSP(FE1), SPORT SUSPENSION(FE3)
1-year Replacement unlimited-mileage warranty
Part Type:
Aftermarket
Brand Description:
Rear Brake Rotor
Product Description:
Rear Disc Brake Rotor
ABS Tone Ring Included:
No
Grade Type:
Performance
Bolt Hole Quantity:
6
Nominal Thickness (Inch):
0.472
Outside Diameter (Inch):
11.8
Discard Thickness (Inch):
0.413
Rust Resistant Coating:
Yes
Construction:
Full Cast
Material:
Cast Iron
Slotted:
No
Solid Or Vented Type Rotor:
Solid
Surface Type:
Smooth
Hat Finish:
Bare
Disc Finish:
Coated
Programming Required:
No
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
GM-recommended replacement part for your GM vehicle's original factory component
Features & Benefits - Bullet 4:
Manufactured to GM OE specification for fit, form, and function
Life Cycle Status:
Announced
Features & Benefits - Bullet 3:
Offering the quality, reliability, and durability of GM OE
Life Cycle Status Description:
Announced - Part has been announced to customers on a paper “New Number Announcement”. Part is active.
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Item Level GTIN:
00808709275503
Height (in) (Inch):
1.5
Signs of Wear & Troubleshooting - Section 1 - Bull:
Visible ridges or deep grooves on the rotor surface.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Vehicle pulls to the left or right when brakes are applied.
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Outside Diameter (Millimeter):
300
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Height (mm) (Millimeter):
37
Bolt Circle Diameter (in) (Inch):
4.528
Bolt Circle Diameter (mm) (Millimeter):
115
Discard Thickness (Millimeter):
10.5
Nominal Thickness (Millimeter):
12
Center Hole Diameter (Millimeter):
71
Center Hole Diameter (Inch):
2.8
Country of Origin:
United States
Weight - Each (Gross Pounds):
12.79
Height - Each (Inch):
03.62
Length - Each (Inch):
15.12
Width - Each (Inch):
14.50
Related Products
ACDelco
ACDelco 177-867 | Rear Disc Brake Rotor
$67.99
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are...
ACDelco
ACDelco 177-1016 | Rear Disc Brake Rotor
$81.59
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are...