ACDelco
ACDelco 177-0958 | Rear Disc Brake Rotor
$234.59
Disc Brake Rotor Rear/Front ACDelco GM Original Equipment 177-0958
click to zoom in
ACDelco 177-867 | Rear Disc Brake Rotor
5 customers are viewing this product
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are GM-recommended replacements for your vehicle's original components. These disc brake rotors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov
BRAND: ACDelco
FEATURES:
- Buick;Cadillac;Oldsmobile;Pontiac
- GM-recommended replacement part for your GM vehicle's original factory component
- Inspected for balance, resulting in smooth brake operation and noise reduction
- Manufactured to GM OE specification for fit, form, and function
- Offering the quality, reliability, and durability of GM OE
SPECIFICS:
| ABS Sensor Ring Included | No |
| Bolt Circle Diameter (in) | 4.6 |
| Bolt Circle Diameter (mm) | 116.8 |
| Bolt Hole Quantity | 5 |
| Center Bore Diameter (in) | 2.7 in |
| Center Bore Diameter (mm) | 70.6 mm |
| Construction | Full Cast |
| Disc Finish | Turned |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Grade Type | Regular |
| Hat Finish | Coated |
| Height (in) | 1.5 |
| Height (mm) | 38.6 |
| Length (in) | 13.12 |
| Lug Quantity | 5 |
| Material | Cast Iron |
| Overall Rotor Diameter (mm) | 281 mm |
| Programming Required | No |
| Rust Resistant Coating | Yes |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Vehicle pulls to the left or right when brakes are applied. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Visible ridges or deep grooves on the rotor surface. |
| Slotted | No |
| Solid Or Vented Type Rotor | Solid |
| Surface Type | Smooth |
| Weight (lb) | 10.1 |
| Width (in) | 12.5 |
DOWNLOADS:
APPLICATIONS:
- 2001-2002 Cadillac Eldorado - Position: Rear
- 2000-2005 Buick Park Avenue - Position: Rear
- 2001-2003 Oldsmobile Aurora - Position: Rear
- 2000-2005 Pontiac Bonneville - Position: Rear
- 2000-2005 Buick LeSabre - Position: Rear
1-year Replacement unlimited-mileage warranty
Part Type:
Aftermarket
Brand Description:
Rear Brake Rotor
Product Description:
Rear Disc Brake Rotor
ABS Tone Ring Included:
No
Grade Type:
Regular
Bolt Hole Quantity:
5
Nominal Thickness (Inch):
0.435
Outside Diameter (Inch):
11
Discard Thickness (Inch):
0.354
Rust Resistant Coating:
Yes
Construction:
Full Cast
Material:
Cast Iron
Slotted:
No
Solid Or Vented Type Rotor:
Solid
Surface Type:
Smooth
Hat Finish:
Coated
Disc Finish:
Turned
Lug Quantity:
5
Programming Required:
No
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
GM-recommended replacement part for your GM vehicle's original factory component
Life Cycle Status:
Discontinued
Features & Benefits - Bullet 4:
Manufactured to GM OE specification for fit, form, and function
Life Cycle Status Description:
Discontinued - Part is being removed from the product line.
Features & Benefits - Bullet 3:
Offering the quality, reliability, and durability of GM OE
Item Level GTIN:
00021625399140
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Weight (lb) (Pound):
10.1
Height (in) (Inch):
1.5
Width (in) (Inch):
12.5
Length (in) (Inch):
13.12
Signs of Wear & Troubleshooting - Section 1 - Bull:
Visible ridges or deep grooves on the rotor surface.
Signs of Wear & Troubleshooting - Section 1 - Bull:
Vehicle pulls to the left or right when brakes are applied.
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Outside Diameter (Millimeter):
281
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Height (mm) (Millimeter):
38.6
Bolt Circle Diameter (in) (Inch):
4.6
Bolt Circle Diameter (mm) (Millimeter):
116.8
Discard Thickness (Millimeter):
8.99
Nominal Thickness (Millimeter):
11.049
Overall Rotor Diameter (mm):
281 mm
Center Hole Diameter (Millimeter):
69
Mounting Bolt Hole Circle Diameter (Inch):
4.52
Mounting Bolt Hole Circle Diameter (Millimeter):
115
Center Hole Diameter (Inch):
2.7
Country of Origin:
United States
Weight - Each (Gross Pounds):
10.10
Height - Each (Inch):
03.62
Length - Each (Inch):
13.12
Width - Each (Inch):
12.50
Related Products
ACDelco
ACDelco 177-0992 | Rear Disc Brake Rotor
$42.49
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are...
ACDelco
ACDelco 177-859 | Rear Disc Brake Rotor
$151.57
ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are...