×
close

Shopping Cart:

Toggle menu
1-321-400-8080

24/7 Customer Service
0

$0.00

0
ACDelco 177-1084 | Rear Brake Drum
click to zoom in

ACDelco 177-1084 | Rear Brake Drum

(No reviews yet) Write a Review
$90.89
Part Number
ACD177-1084
UPC:
707773701928
Condition:
New
5 customers are viewing this product

video gallery

Description

ACDelco GM Original Equipment Brake Drums are cylinder shaped bowls where the wheel cylinder presses the brake shoes outward against the inside of the drum. Drums are typically found on older vehicles and on the rear axles of trucks and some cars. These original equipment brake drums are manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

BRAND: ACDelco

FEATURES:

  • Chevrolet|Pontiac
  • GM-recommended replacement part for your GM vehicle's original factory component
  • Have a rust-preventative coating to help protect against corrosion
  • Inspected for balance, resulting in smooth brake operation and noise reduction
  • Manufactured to GM OE specification for fit, form, and function
  • Offering the quality, reliability, and durability of GM OE

SPECIFICS:

Bolt Circle Diameter (in)4.330709
Bolt Circle Diameter (mm)110
Bolt Hole Quantity5
Drum Center Bore Diameter (in)2.580827
Drum Center Bore Diameter (mm)65.553
Good Maintenance Practices - Section 1 - Bullet 5The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 1 - Bullet 6Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Good Maintenance Practices - Section 1 - Bullet 7Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 8Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 9Check the thickness of your brake pads.
Good Maintenance Practices - Section 2 - Bullet 5The following should be conducted by a qualified technician:
Good Maintenance Practices - Section 2 - Bullet 6Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 7Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 8Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 9Parking brake adjustments (as needed).
Height (in)3.62
Length (in)13.12
MaterialCast Iron
Mount Hole Diameter (in)0.5511811 in
Mount Hole Diameter (mm)14 mm
Programming RequiredNo
Signs of Wear & Troubleshooting - Section 1 - Bullet 6Squealing or scraping noises.
Signs of Wear & Troubleshooting - Section 1 - Bullet 7Brake pedal pulsation (not to be confused with normal ABS operation).
Weight (lb)11.86
Width (in)12.5

APPLICATIONS:

  • 2009-2010 Chevrolet Cobalt - Position: Rear
    • SOFT RIDE SUSP(FE1), ALUM WHL(NZ0), ALUM WHEEL(PFE)
  • 2009-2010 Pontiac G5 - Position: Rear
    • SOFT RIDE SUSP(FE1), ALUM WHL(NZ0), ALUM WHEEL(PFE)
  • 2009-2011 Chevrolet HHR - Position: Rear
    • SOFT RIDE SUSP(FE1), SPORT SUSPENSION(FE3)

Attributes
Product type:
Aftermarket
Brand Description:
Rear Brake Drum
Bolt Hole Quantity:
5
Outside Diameter (Inch):
10.7874
Material:
Cast Iron
Inside Diameter (Inch):
9.003937
Programming Required:
No
Maximum Brake Diameter (Discard) (Inch):
9.07874
Hazardous Material:
No
Minimum Order Quantity:
1
Features & Benefits - Bullet 2:
Have a rust-preventative coating to help protect against corrosion
Features & Benefits - Bullet 4:
Offering the quality, reliability, and durability of GM OE
Features & Benefits - Bullet 3:
GM-recommended replacement part for your GM vehicle's original factory component
Features & Benefits - Bullet 1:
Inspected for balance, resulting in smooth brake operation and noise reduction
Weight (lb) (Pound):
11.86
Height (in) (Inch):
3.62
Width (in) (Inch):
12.5
Length (in) (Inch):
13.12
Signs of Wear & Troubleshooting - Section 1 - Bull:
Brake pedal pulsation (not to be confused with normal ABS operation).
Signs of Wear & Troubleshooting - Section 1 - Bull:
Squealing or scraping noises.
Features & Benefits - Bullet 5:
Manufactured to GM OE specification for fit, form, and function
Life Cycle Status:
Discontinued
Good Maintenance Practices - Section 1 - Bullet 1:
Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Life Cycle Status Description:
Discontinued - Part is being removed from the product line.
Good Maintenance Practices - Section 1 - Bullet 2:
Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Item Level GTIN:
00707773701928
Good Maintenance Practices - Section 1 - Bullet 3:
Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Good Maintenance Practices - Section 1 - Bullet 4:
Check the thickness of your brake pads.
Good Maintenance Practices - Section 1 - Header:
The following inspections and maintenance procedures can help prevent potential brake problems.
Good Maintenance Practices - Section 2 - Bullet 1:
Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2:
Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - Bullet 3:
Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4:
Parking brake adjustments (as needed).
Inside Diameter (Millimeter):
228.7
Outside Diameter (Millimeter):
274
Good Maintenance Practices - Section 2 - Header:
The following should be conducted by a qualified technician:
Mount Hole Diameter (in):
0.5511811 in
Mount Hole Diameter (mm):
14 mm
Bolt Circle Diameter (in) (Inch):
4.330709
Bolt Circle Diameter (mm) (Millimeter):
110
Maximum Brake Diameter (Discard) (Millimeter):
230.6
Drum Center Bore Diameter (in) (Inch):
2.580827
Drum Center Bore Diameter (mm) (Millimeter):
65.553
Country of Origin:
Mexico
Weight - Each (Gross Pounds):
11.86
Height - Each (Inch):
03.62
Length - Each (Inch):
13.12
Width - Each (Inch):
12.50



Need help? We're available at1-321-400-8080 - Email us atinfo@partsonnet.net orlive help
to top